Arduino Nano XL Link Adds CAN FD, RS485 and Ethernet
- Ananthu Ashok
- 954 reads
Arduino’s Nano XL Link pairs a 120MHz Cortex-M33 with CAN FD, RS485 and Ethernet for automation and building control projects.

The Arduino Nano XL Link brings three wired network interfaces onto a compact development board: CAN FD, RS485 and 10/100Mbps Ethernet. For engineers prototyping automation and building control systems, the practical change is less interface hardware to add before connecting a controller to field devices or a local network.

Arduino introduced the Nano XL Link and the companion Nano XL Link Connector Carrier at electronica 2026. The board keeps the Nano form factor while targeting machine control, fieldbus gateways, smart lighting, HVAC and energy management. Those are stated application areas; Arduino has not provided performance figures or test conditions showing how the board behaves in a particular system.


Three wired interfaces on the board
The Nano XL Link uses a Microchip PIC32CK2051SG01144 microcontroller, built around a 32-bit Arm Cortex-M33 processor running at 120MHz. It has 2MB of flash and 512KB of RAM. That memory and compute specification gives developers the resources to build control firmware with communication tasks on the same board, though the available details don’t specify operating limits or application-level throughput.

Each network connection has dedicated interface hardware. A Texas Instruments TCAN3414 transceiver handles CAN FD, while a THVD2410 transceiver supports RS485. Ethernet uses a Microchip KSZ8081 PHY and supports 10/100Mbps. Arduino gives a maximum CAN FD speed of 8Mbps. The figures describe interface capability; achievable rates in a finished system depend on configuration and network conditions, details not supplied for this board.

Combining these links can help a prototype communicate across different parts of an installation. CAN FD and RS485 are suited to wired device networks, while Ethernet provides a connection to equipment and infrastructure using that interface. A controller intended to bridge networks still needs firmware that manages messages, timing and fault handling; the presence of the physical interfaces alone doesn’t establish gateway behavior or compatibility with a particular device.

Expansion and enclosure integration
Two 30-pin, double-row connectors expose digital and analogue I/O, PWM, UART, SPI and I2C. A Qwiic connector provides another route for connecting compatible sensors and devices. That mix gives developers options for local peripherals alongside the board’s wired network ports, while the connector-carrier design addresses the separate task of mounting and wiring the board in an enclosure.

The Nano XL Link Connector Carrier adds screw terminals for CAN FD and RS485, an RJ45 Ethernet interface and a DIN-rail mounting arrangement. Arduino describes the carrier as suitable for industrial enclosures up to 4U in size. The carrier therefore shifts the physical connections toward familiar field wiring and enclosure mounting, although the published details don’t specify terminal ratings, environmental limits or enclosure requirements.
For a bench prototype, the board’s compact format and exposed interfaces may simplify early hardware integration. For a cabinet build, the carrier provides a more direct path to screw-terminal wiring, an Ethernet cable and DIN-rail installation. Designers will still need to confirm electrical and mechanical fit against their own installation requirements once full product documentation is available.
Development support and what remains open
Arduino says the Nano XL Link can be programmed with the Arduino IDE and Arduino Cloud, and it supports the Arduino Zephyr core. That offers several software routes for development, but the announcement doesn’t detail supported libraries, peripheral drivers, real-time performance, or how cloud tools fit into deployments that operate without a continuous internet connection.
The stated use cases span machine controllers, fieldbus gateways, lighting, HVAC and energy management. The combination of Cortex-M33 processing, CAN FD, RS485 and Ethernet makes those applications plausible targets for prototyping, but suitability for a production system will depend on requirements the available specifications don’t address, including interface isolation, electrical protection, operating temperature and software behavior under faults.
Arduino has not announced pricing or availability for either the Nano XL Link or its Connector Carrier. Those details, along with fuller electrical and mechanical documentation, will determine how easily teams can assess the boards for deployment beyond development and evaluation.