RECOM Adds 720W IP67 Supplies for Decentralised Industrial Power
- Saba Aafreen
- 857 reads
RECOM’s new 720W RACPRO1 supplies support cabinet-free installation; one model adds four isolated, current-limited outputs with an integrated e-Fuse.

Moving power conversion closer to industrial equipment can cut the wiring between a central cabinet and distributed loads. RECOM has added two 720W models to its RACPRO1 family for that approach: the RACPRO1-DP-T720 and RACPRO1-DP-T720-4SP. Both carry an IP67 rating and are designed for installation outside control cabinets, while the 4SP version adds four isolated outputs with individual electronic protection.


Power near the point of use
Conventional industrial installations commonly place power supplies in a control cabinet, then distribute power to equipment elsewhere in the machine or facility. A decentralised arrangement puts conversion nearer to the loads. That can shorten wiring runs and give machine builders more freedom in equipment layout, though the power supply itself must be suitable for its installation environment.

RECOM’s two new units are intended to address that use case with an IP67-rated enclosure. Their stated applications include factory and process automation, machine building, intralogistics, battery energy storage, water treatment, HVAC and agriculture. The range gives designers a choice between a single-output supply and a model that combines power conversion with per-output electronic fusing.

Input range and output performance
The RACPRO1-DP-T720 accepts three-phase AC input from 320VAC to 600VAC, or DC input from 425VDC to 800VDC. RECOM specifies efficiency of up to 96.8 percent. The unit can deliver its full 720W output up to +45°C with convection cooling, so the stated operating point does not depend on forced-air cooling.

For short-term overload conditions, the supply can provide up to 1080W for 5 seconds. That temporary capacity may help accommodate brief load peaks, but it is distinct from the continuous 720W rating. The published figures identify the duration and power level; they don’t provide further details about overload repetition or derating above +45°C.

RECOM also gives a power density of 400W/L. For designers working with limited space near machinery, that figure offers a way to compare the unit’s packaging against other supplies, although the installation still needs room for connections and any required clearances.

Four isolated outputs on the 4SP model
The RACPRO1-DP-T720-4SP adds four isolated outputs, each with an adjustable current limit through its built-in e-Fuse. This lets a single supply feed multiple loads with output-level protection. The isolated outputs and adjustable limits make the model relevant where different branches need separate current settings or where a fault on one branch needs to be managed independently.

RECOM lists safe start-up for capacitive loads, selectable hiccup or trip modes, and priority disconnect during overload as further features. These functions give equipment designers options for handling startup demand and overload response. The choice of hiccup or trip behaviour affects how a protected output responds after an overcurrent event; the available description doesn’t specify the detailed timing or reset conditions, so those should be checked against the product documentation during design.
The 4SP’s integrated protection can reduce the need to assemble separate electronic fusing alongside a power supply. That may simplify the power distribution hardware around a machine, while putting more of the branch-protection design inside the supply. System designers will still need to match each output’s current limit and protection behaviour to its load.
Choosing between the two series
The RACPRO1-DP-T720 is the straightforward option where a 720W supply is needed and downstream distribution is handled separately. The RACPRO1-DP-T720-4SP combines that power conversion role with four protected outputs. RECOM Product Manager Michael Peters described the two models as addressing different industrial application requirements, with the 4SP combining conversion and an e-Fuse in one compact unit.
For machine builders, the decision comes down to the distribution architecture: one supply feeding a system designed around external branch protection, or a supply with four isolated, current-limited outputs built in. In either case, the ratings and operating conditions provide the starting point for checking input compatibility, expected load peaks, ambient temperature and installation location. The main practical change is that a 720W industrial supply can now be specified for placement near equipment, with an integrated multi-output protection option available where the load layout calls for it.
Product details are available from RECOM.