Japan–Germany Fusion Deals Target Superconducting Tape, Gyrotrons and Stellarators
- Robert Johnson
- 458 reads
Proxima Fusion’s agreements with Fujikura and Kyoto Fusioneering focus on superconducting tape production, plasma heating and fuel-cycle technology.

The Japan–Germany fusion cooperation announced during German chancellor Friedrich Merz’s visit to Japan puts manufacturing capacity alongside reactor research. Proxima Fusion, a German company developing a stellarator power plant, signed agreements with Fujikura and Kyoto Fusioneering covering two demanding parts of its plans: high-temperature superconducting tape and systems for heating plasma and processing fusion fuel.
The proposed plant is planned for Gundremmingen, Germany, by the end of the next decade. Proxima’s demonstrator is expected to require 20,000 km of high-temperature superconducting (HTS) tape; the commercial plant would need twice that amount. Those quantities make tape production a central engineering and supply challenge, rather than a peripheral procurement detail.
Scaling the stellarator’s superconducting coils
Proxima is developing a stellarator, a reactor configuration that confines hot plasma using magnetic fields shaped by a set of complex coils. Its design calls for dozens of non-planar coils made with HTS tape. The agreement with Japanese conglomerate Fujikura concerns Proxima’s plan to build an HTS tape factory in Lower Saxony. Proxima says it expects to draw on Fujikura’s manufacturing expertise for the project.
The tape’s role is tied directly to the reactor’s magnetic system: the coils must produce the fields that hold plasma in place. Turning that design into a power plant therefore depends on producing a large amount of suitable conductor, then incorporating it into coils with demanding shapes and operating requirements. The announced volume gives a sense of the manufacturing scale involved, though the companies have not provided further details here about factory capacity, tape specifications or production timing.
Proxima’s design draws on research at the Max Planck Institute’s Wendelstein 7-X facility, described as the world’s largest stellarator. Stellarators and tokamaks both use magnetic fields to confine hot plasma, where fusion reactions can occur. Their magnetic configurations differ, however, and that difference affects the engineering of the confining system.
Stellarator proponents argue that these machines can achieve confinement quality with lower electrical currents than tokamaks. The practical case for any reactor design will depend on how its plasma performance, component lifetime, construction demands and power requirements develop. The industrial agreements announced here address some of the hardware and production work needed to move a stellarator concept toward a plant.
Heating and fuel-cycle systems
Kyoto Fusioneering’s memorandum of understanding with Proxima covers support for next-generation gyrotrons and fuel-cycle technologies. Gyrotrons are used to heat plasma with high-frequency electromagnetic waves. In a fusion system, plasma heating must bring the fuel to conditions where fusion reactions can take place, while the fuel cycle concerns how fusion fuel is supplied, managed and recovered within the plant.
The agreement identifies areas of joint development, but does not give technical specifications, schedules or a division of engineering responsibilities. Those details matter: heating equipment has to work with the reactor’s plasma and magnetic configuration, while fuel-cycle systems have to fit the plant’s operating design. For now, the memorandum signals that Proxima is seeking expertise beyond the stellarator vessel and its coils.
More than one fusion approach in the agreements
The set of commercial agreements also includes work on other confinement concepts. Kyoto Fusioneering signed an MoU with Focused Energy, which is developing laser-driven inertial fusion. That approach differs from magnetic confinement in both tokamaks and stellarators: it uses lasers to drive fusion rather than holding plasma in a magnetic field configuration.
German company Gauss Fusion and Japanese company Helical Fusion signed a joint statement of intent covering modular and helical stellarator technology. These arrangements point to a broad set of industrial connections across Japan and Germany, while keeping distinct fusion approaches in view. The announcements do not set out project budgets, milestones or technical performance targets for these agreements.
Manufacturing is part of the fusion challenge
Proxima CEO and co-founder Francesco Sciortino said the global effort to develop fusion power will be won through factories and supply chains. He pointed to Japan’s fusion engineering capabilities and Germany’s stellarator engineering and industrialisation experience. His comments frame the partnerships as a way to connect specialist engineering with the production capacity a power plant would demand.
During the visit, Merz and Japanese prime minister Sanae Takaichi also signed a joint declaration covering cooperation in advanced technology, including fusion, space, clean hydrogen, quantum technology and synchrotron radiation science. Takaichi described industrial technology cooperation between the two countries as important, citing their manufacturing experience and industrial capabilities.
The immediate engineering question is whether the agreements lead to qualified components, production facilities and integrated systems that can support Proxima’s proposed schedule. The stated tape requirement already signals the scale of the task. Progress will depend on turning design requirements into manufacturing processes and equipment that can operate together in a working plant.